Wi-Fi problems
Without Internet nothing is there and Internet is the thing where we can learn many things in one single environment. Wi-Fi,Networks can be wireless and wired and compared to that many paths are designed for this by taking the path from the underground as like a Leased Line services and the wireless.Wifi as by the name wireless connection,as speed as wired and has large capacity.Problems and issues may also arise in this wireless connections.In this tutorial we will take one issue and solve this where this issue is faced by most of us.Kindly comment below if your facing any issues other than the mentioned one in the post so that we will discuss how to resolve it.For example how to increase the speed of Wi-Fi and many queries that you have.Speed capacity is dependent upon the bandwidth.
Each and every PC has different IP address where that is used to identified in a group of networks.This Ip's are of ranged and these are given by using DHCP protocol where they can communicate with each other.If suppose if your PC is our of DHCP configuration then you will be getting the error which is above shown.How to resolve this ?
Sometimes your PC is also identified by using your MAC address of the PC.This issue can be resolved in 2 methods
Method 1
Open the RUN box by pressing Windows + R and in that type ncpa.cpl so that it takes you directly to network connections page instead of going to Control Panel.Now in that select your network and give right click once and go to properties
Now you will be able to see one dialogue box with two tabs in it one is the networking tab and sharing tab like this.
Jump to the TCP/IPv4 option and there you will find two options where the first is automatic and with this thing you're not helpful when you get these type of errors.If you try to ping your IP in CMD it will be showing as destination host unreachable.So automatic is not useless completely it can be helpful by following the below idea.
Open the Command prompt by Pressing Windows+X so that the you will be able to open the CMD with Administrative privileges
In that Command prompt type "netsh winsock reset" and netsh is thing which allows you to configure any interface from remotely,Winsock is like a bridge where communication happens between the installed networking software in your PC and the service of the network and Reset is the things which resets all the last networks connected to the system
Hit enter by placing that command in box and make sure to restart the system,Once after restart is complete even now it wont be able to connect so now again open the Command prompt and this type enter the following command "netsh ip int reset" and hit enter where now the Ip address of your PC will be reverted to default.
After this perform troubleshooting go to control panel-->Network and Internet and in this go to=>Network and sharing centre where you can see troubleshooting option and click on it let the troubleshooting begun.
Once the troubleshooting is done you will be getting an error like DHCP has been disable and along you will find a fixation button on the right side just click on that to fix and once the trouble-shooting is done it will be showing in the green color as fixed.Restart your PC once again for the final time and check network status bar now it will be showing connected.
Read more: VPN As proxy
Method 2:
It depends upon the allocation of Ip address which is assigned to PC manually,allocation of IP address manually now only thing here is you need to use the concept of LAN.If suppose the IP of your friends PC is 192.168.10.22 and the subnet mask of 255.255.255.0 and the default gateway according to the range and now if you get this type of errors just simply open the Run box and type ncpa.cpl and hit enter.Now click on the option of your network and go to properties as of same and now this time select the option to give Ip address of your own by clicking on the option use the following ip address where now you will be able to add IP address of you own.The IP address of your PC will be 192.168.10.23 which will be the next host and the subnet mask remains the same,What we did now is assigning IP address based on DHCP configuration.In this way you can resolve the issue.
Wi-Fi issues are common and this can be resolved easily sometimes and sometimes take much longer time than the expected.You can also some of the tools which are by default by the Microsoft windows to fix this type of issues .CMD is a powerful tool where it can fix this type of issues and provides you some knowledge on the working of the operating system and functioning of the network.If the post had made your issue resolved kindly comment below if not comment whats the exact issue your facing we will make new post on the considered one.
This is dummy text. It is not meant to be read. Accordingly, it is difficult to figure out when to end it. But then, this is dummy text. It is not meant to be read. Period.
ConversionConversion EmoticonEmoticon